add Waveshare ESP32-S3-Touch-AMOLED-2.06

.github/workflows/main.yml

@@ -132,6 +132,7 @@
             - { env: "waveshare-esp32-c5-lcd-147" }
             - { env: "waveshare-esp32-c6-lcd-147" }
             - { env: "waveshare-esp32-c6-lcd-130" }
+            - { env: "waveshare-esp32-s3-touch-amoled-206"}
             - { env: "ES3C28P"                    }
             - { env: "xteink-x3-x4"               }
             - { env: "xteink-x4pro"               }

boards/waveshare-esp32-s3-touch-amoled-206/interface.cpp

@@ -0,0 +1,97 @@
+#include "display/Arduino_CO5300.h"
+#include "hal/device.h"
+#include "hal/inputs/buttons.h"
+#include "hal/inputs/touch.h"
+
+#include "idf/launcher_platform.h"
+#include "powerSave.h"
+#include <Wire.h>
+#include <XPowersLib.h>
+#include <interface.h>
+
+#define BOARD_I2C_SDA 15
+#define BOARD_I2C_SCL 14
+#define BOARD_TOUCH_INT 38
+#define BOARD_TOUCH_RST 9
+#define BOARD_TOUCH_ADDRESS 0x38
+#define BTN1 0
+#define BTN2 10
+
+XPowersAXP2101 axp2101;
+
+static bool touch_OK = false;
+
+static DeviceTouch touchCfg() {
+    DeviceTouch cfg;
+    cfg.pin_rst = BOARD_TOUCH_RST;
+    cfg.pin_irq = BOARD_TOUCH_INT;
+    return cfg;
+}
+
+void _setup_gpio() {
+    Wire.begin(BOARD_I2C_SDA, BOARD_I2C_SCL);
+    axp2101.init(Wire, BOARD_I2C_SDA, BOARD_I2C_SCL);
+
+    axp2101.clearIrqStatus();
+
+    axp2101.enableVbusVoltageMeasure();
+    axp2101.enableBattVoltageMeasure();
+    axp2101.enableSystemVoltageMeasure();
+    axp2101.enableTemperatureMeasure();
+
+    // It is necessary to disable the detection function of the TS pin on the board
+    // without the battery temperature detection function, otherwise it will cause abnormal charging
+    axp2101.disableTSPinMeasure();
+
+    // Disable all interrupts
+    axp2101.disableIRQ(XPOWERS_AXP2101_ALL_IRQ);
+    // Clear all interrupt flags
+    axp2101.clearIrqStatus();
+    // Enable the required interrupt function
+    axp2101.enableIRQ(
+        XPOWERS_AXP2101_BAT_INSERT_IRQ | XPOWERS_AXP2101_BAT_REMOVE_IRQ |    // BATTERY
+        XPOWERS_AXP2101_VBUS_INSERT_IRQ | XPOWERS_AXP2101_VBUS_REMOVE_IRQ |  // VBUS
+        XPOWERS_AXP2101_PKEY_SHORT_IRQ | XPOWERS_AXP2101_PKEY_LONG_IRQ |     // POWER KEY
+        XPOWERS_AXP2101_BAT_CHG_DONE_IRQ | XPOWERS_AXP2101_BAT_CHG_START_IRQ // CHARGE
+        // XPOWERS_AXP2101_PKEY_NEGATIVE_IRQ | XPOWERS_AXP2101_PKEY_POSITIVE_IRQ   |   //POWER KEY
+    );
+
+    hal_buttons_init_2(DeviceButtons{BTN1, BTN2}, 600);
+
+    touch_OK = hal_touch_init(touchCfg(), BOARD_TOUCH_ADDRESS);
+}
+
+int getBattery() {
+    int percent = axp2101.getBatteryPercent();
+    return percent;
+}
+
+void _setBrightness(uint8_t brightval) {
+    auto *panel = static_cast<Arduino_CO5300 *>(tft->outputDriver());
+    if (panel) panel->setBrightness((brightval * 255) / 100);
+}
+
+
+void InputHandler(void) {
+    if (touch_OK) {
+        static unsigned long tm = 0;
+        LTouchPoint t;
+        bool touched = hal_touch_read(touchCfg(), t);
+        vTaskDelay(pdMS_TO_TICKS(50));
+        if ((launcherMillis() - tm) > 200 || LongPress) { // one reading each 500ms
+            if (touched) {
+                tm = launcherMillis();
+                if (!hal_touch_apply(t)) return;
+            }
+        }
+    }
+
+    hal_buttons_poll_2();
+    return;
+}
+
+void powerOff() { axp2101.shutdown(); }
+
+void reboot() {
+    ESP.restart();
+}

boards/waveshare-esp32-s3-touch-amoled-206/platformio.ini

@@ -0,0 +1,54 @@
+[env:waveshare-esp32-s3-touch-amoled-206]
+board = esp32s3
+board_build.partitions = support_files/custom_32Mb.csv
+
+board_build.arduino.memory_type = qio_qspi
+board_upload.flash_size = 32MB
+board_upload.maximum_size = 33554432
+
+build_src_filter =${env.build_src_filter} +<../boards/waveshare-esp32-s3-touch-amoled-206>
+build_flags =
+	${env.build_flags}
+	-DBOARD_HAS_PSRAM
+	-DARDUINO_USB_MODE=1
+	-DARDUINO_USB_CDC_ON_BOOT=1
+
+	-D DEVICE_NAME='"Waveshare ESP32-S3 Touch AMOLED 2.06"'
+	-D OTA_TAG='"waveshare_amoled_206"'
+	-D OTA_EXTRA='"esp=S3"'
+	-D LAUNCHER_DEFAULT_SPIFFS_THRESHOLD=0x500000
+
+	-D ROTATION=0
+	-D DIMMER_SETUP=20
+	-D HAS_2_BUTTONS=1
+	-D BUTTONS_IDF_COMPONENT=1
+	-D HAS_TOUCH=1
+	-D TOUCH_CTRL_FT6X36=1
+
+	-D ROUND_EDGE_SIZE=57 # to use when the rounded edges hide text or icons on screen
+	-D TFT_DATABUS_N=1			# Arduino_ESP32QSPI
+	-D TFT_DISPLAY_DRIVER_N=41	# CO5300
+	-D TFT_WIDTH=502
+	-D TFT_HEIGHT=410
+	-D TFT_CS=12
+	-D TFT_RST=8
+	-D TFT_SCLK=11
+	-D TFT_D0=4
+	-D TFT_D1=5
+	-D TFT_D2=6
+	-D TFT_D3=7
+	-D TFT_IPS=0
+	-D TFT_COL_OFS1=0
+	-D TFT_ROW_OFS1=22
+	-D TFT_COL_OFS2=0
+	-D TFT_ROW_OFS2=22
+
+	-D SDCARD_CS=17
+	-D SDCARD_SCK=2
+	-D SDCARD_MISO=3
+	-D SDCARD_MOSI=1
+
+
+lib_deps =
+	${env.lib_deps}
+	https://github.com/bmorcelli/ESP32_Button

platformio.ini

@@ -94,6 +94,7 @@ default_envs =
 	; waveshare-esp32-c5-lcd-147
 	; waveshare-esp32-c6-lcd-147
 	; waveshare-esp32-c6-lcd-130
+	; waveshare-esp32-s3-touch-amoled-206
 	; xteink-x3-x4
 	; xteink-x4pro
 	; xueersi-xiaomiao

support_files/custom_32Mb.csv

@@ -0,0 +1,5 @@
+# Name,     Type, SubType,   Offset,   Size,    Flags
+nvs,        data, nvs,       0x9000,   0x5000,
+otadata,    data, ota,       0xE000,   0x2000,
+app0,       app,  test,      0x10000,  0x210000,
+coredump,   data, coredump,  0x220000, 0x10000,