firstrun: set per-model hostname on the NanoPi 6-series unified image

packages/bsp/common/usr/lib/armbian/armbian-firstrun

@@ -12,6 +12,27 @@
 . /lib/lsb/init-functions
 . /usr/lib/armbian/armbian-common
 
+# Apply a new system hostname once and reconcile the 127.0.1.1/::1 records in
+# /etc/hosts written at build time (loopback names, aliases and comments are
+# left untouched). No-op only when the target is empty. The /etc/hosts
+# reconciliation runs even when new==old (skipping only the hostnamectl call
+# itself): a prior run can have set the hostname successfully but failed the
+# /etc/hosts edit, and a retry must still repair those records rather than
+# short-circuit on "already current".
+set_new_hostname() {
+	local new="$1" old esc_new
+	old="$(hostname)"
+	[[ -z "$new" ]] && return 0
+	if [[ "$new" != "$old" ]]; then
+		hostnamectl set-hostname "$new" || return 1
+	fi
+	esc_new=$(printf '%s' "$new" | sed 's#[\\/&]#\\&#g')
+	sed -i -E \
+		-e "s|^(127\.0\.1\.1[[:space:]]+)[^[:space:]#]+|\1${esc_new}|" \
+		-e "s|^(::1[[:space:]]+localhost[[:space:]]+)[^[:space:]#]+|\1${esc_new}|" \
+		/etc/hosts
+}
+
 case "$1" in
 	start)
 
@@ -129,17 +150,62 @@ case "$1" in
 	[[ "${LINUXFAMILY}" == meson64 ]] && set_fixed_mac
 	[[ "${BOARD}" == nanopi-r6* ]] && set_fixed_mac
 
-	# adjust hostname for rpi's
+	# adjust hostname for rpi's: the single arm64 image boots the whole Pi 3B+
+	# onward lineup, so pick a per-model hostname from the board model string.
+	# Ordered most-specific-first so e.g. "Model B Plus" wins over "Model B".
 	if [[ "${BOARD}" == rpi4b && "$(hostname)" == rpi4b ]]; then
 		BOARD_NAME=$(cat /proc/device-tree/model | tr '\0' '\n' | sed -E 's/ Rev [0-9.]+$//')
-		[[ "$BOARD_NAME" == *"Zero 2 W"* ]] && NEW_HOSTNAME="rpizero2w"
-		[[ "$BOARD_NAME" == *"Pi 5 Model B"* ]] && NEW_HOSTNAME="rpi5b"
-		[[ "$BOARD_NAME" == *"Pi 3 Model B"* ]] && NEW_HOSTNAME="rpi3b"
-		[[ "$BOARD_NAME" == *"Pi 400"* ]] && NEW_HOSTNAME="rpi400"
-		# Update /etc/hosts to reflect the new hostname
-		sed -i "s/$(hostname)/$NEW_HOSTNAME/g" /etc/hosts
-		# Change the hostname
-		hostnamectl set-hostname "$NEW_HOSTNAME"
+		NEW_HOSTNAME=""
+		# Model strings are the upstream RPi kernel DT values (arm64 / 64-bit
+		# lineup only). Compute Modules report their carrier-board string, so a
+		# substring of the SoM name is matched.
+		case "$BOARD_NAME" in
+			*"Compute Module 3"*) NEW_HOSTNAME="rpicm3" ;;
+			*"Compute Module 4S"*) NEW_HOSTNAME="rpicm4s" ;;
+			*"Compute Module 4"*) NEW_HOSTNAME="rpicm4" ;;
+			*"Compute Module 5 Lite"*) NEW_HOSTNAME="rpicm5lite" ;;
+			*"Compute Module 5"*) NEW_HOSTNAME="rpicm5" ;;
+			*"Zero 2 W"*) NEW_HOSTNAME="rpizero2w" ;;
+			*"Pi 3 Model A+"*) NEW_HOSTNAME="rpi3aplus" ;;
+			*"Pi 3 Model B+"*) NEW_HOSTNAME="rpi3bplus" ;;
+			*"Pi 3 Model B"*) NEW_HOSTNAME="rpi3b" ;;
+			*"Pi 400"*) NEW_HOSTNAME="rpi400" ;;
+			*"Pi 4 Model B"*) NEW_HOSTNAME="rpi4b" ;;
+			*"Pi 500"*) NEW_HOSTNAME="rpi500" ;;
+			*"Pi 5"*) NEW_HOSTNAME="rpi5b" ;;
+		esac
+		# Leaves the default rpi4b hostname in place when no model matched.
+		# A failure here must not reach the service-disable below - if it did, a
+		# transient hostnamectl/sed failure would strand the board on the wrong
+		# hostname forever instead of retrying on the next boot.
+		set_new_hostname "$NEW_HOSTNAME" || exit 1
+	fi
+
+	# adjust hostname for the FriendlyElec NanoPi 6-series unified image.
+	# A single image boots on several boards; the unified U-Boot detects the
+	# model via SARADC and exports nanopi6_model=<model> as its own token on the
+	# kernel command line, present only on these images. Parse it word-by-word so
+	# it can never match text embedded inside another kernel argument.
+	nanopi6_model=""
+	for arg in $(cat /proc/cmdline); do
+		case "$arg" in
+			nanopi6_model=*) nanopi6_model="${arg#nanopi6_model=}"; break ;;
+		esac
+	done
+	if [[ -n "$nanopi6_model" ]]; then
+		NEW_HOSTNAME=""
+		case "$nanopi6_model" in
+			r6s) NEW_HOSTNAME="nanopi-r6s" ;;
+			r6c) NEW_HOSTNAME="nanopi-r6c" ;;
+			m6) NEW_HOSTNAME="nanopi-m6" ;;
+			m6v2) NEW_HOSTNAME="nanopi-m6v2" ;;
+			t6) NEW_HOSTNAME="nanopct6" ;;
+			t6-lts) NEW_HOSTNAME="nanopct6-lts" ;;
+			t6-lts-plus) NEW_HOSTNAME="nanopct6-lts-plus" ;;
+		esac
+		# Same reasoning as the rpi4b case above: don't let a failed hostname
+		# update reach the service-disable, or first-run never gets to retry.
+		set_new_hostname "$NEW_HOSTNAME" || exit 1
 	fi
 
 	# Remove KDE Neon base files upgrade pin