Skip to content
Merged
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
24 changes: 24 additions & 0 deletions content/raptacon/quizzes/README.md
Original file line number Diff line number Diff line change
@@ -0,0 +1,24 @@
# Safety quizzes

One file per quiz. Each quiz is the written half of a safety sign-off: you pass the quiz, then a mentor
watches you use the tool and signs you off on the skill (`item`). The quiz never replaces the sign-off.

```yaml
quiz:
id: band-saw # file name without .yml
name: Band saw safety quiz
item: tool-band-saw # the skill this quiz is for
pass: 100 # percent needed to pass; retakes are unlimited
authored_by: [{name, github?}]
source: where the original questions came from
questions:
- q: The question.
choices: [A, B, C, D] # shown shuffled
answer: B # the correct choice, word for word
# or answers: [A, C] # "check all that apply": every listed choice, and only those
why: One line on why, shown after a wrong answer.
origin: schoology | new # ported from the Schoology test, or added for this bank
review: true # new or changed: a mentor should read it before it counts
```

Choices never refer to each other by letter ("both a and b"): the quiz shuffles them.
153 changes: 153 additions & 0 deletions content/raptacon/quizzes/band-saw.yml
Original file line number Diff line number Diff line change
@@ -0,0 +1,153 @@
# Band saw: the written half of tool-band-saw. Questions 1-11 are the Schoology "Band Saw
# Quiz" (ID 5317); 12-16 are new; 17-21 replace the band saw parts diagram worksheet
# (it had no answer key) with questions about what each part does.

quiz:
id: band-saw
name: Band saw safety quiz
item: tool-band-saw
pass: 100
authored_by: # Corey and Marilyn wrote the Schoology originals; Chris added the new questions
- {name: Corey Kesler}
- {name: Marilyn Kemp}
- {name: Chris Hirsch, github: ChrisHirsch}
source: Schoology "Band Saw Quiz" (ID 5317) and the band saw parts diagram

questions:
- q: How high above the stock should the upper blade guard and guides be set?
choices: [1/16 to 1/8 inch, 1/8 to 1/4 inch, 1/4 to 1/2 inch, 1/2 to 1 inch]
answer: "1/8 to 1/4 inch"
why: Just above the stock, so as little blade as possible is exposed and the blade is supported close to the cut.
origin: schoology

- q: When you cut a small piece, you should always...
choices: [use a push stick (ask a mentor to show you how), hold it with your fingertips, use a round guide, get someone to hold it for you]
answer: "use a push stick (ask a mentor to show you how)"
why: Small parts bring your fingers close to the blade. A push stick keeps them away.
origin: schoology
review: true # reworded from "consult a veteran/mentor to learn how to use a push stick"

- q: Relief cuts on the band saw...
choices: [keep the blade from binding in tight curves, are only for hardwood, are cuts made in a hurry, are only for softwood]
answer: "keep the blade from binding in tight curves"
why: Cutting relief cuts first lets waste fall away, so the blade isn't twisted around a tight curve.
origin: schoology

- q: Before making any cut, you first...
choices: ["check the stock is free of nails, screws or other obstructions", "turn the saw on", "take off your safety glasses", "start cutting slowly"]
answer: "check the stock is free of nails, screws or other obstructions"
why: Hidden metal can break the blade or throw the piece.
origin: schoology

- q: When cutting freehand on the band saw, it is safe to...
choices: [force the stock around curves, keep the stock flat on the table, hold round stock in your hand, back out of a curved cut while the saw runs]
answer: "keep the stock flat on the table"
why: Flat on the table, the blade pushes the stock down. Round or tilted stock can spin and pull your hand in.
origin: schoology

- q: When is it safe to have your hand in line with the blade?
choices: [When your hand is more than 2 inches away, When your hand is more than 4 inches away, Only when the saw is off and stopped, When your hand is more than 6 inches away]
answer: "Only when the saw is off and stopped"
why: If the stock slips, a hand in line with the blade goes straight into it.
origin: schoology

- q: While running the band saw, it is a safe practice to...
choices: [reach across the table while the blade is running, keep a balanced stance the whole time, open the wheel covers carefully, leave the scraps until the end of the meeting]
answer: "keep a balanced stance the whole time"
why: Off balance, a slip pushes your hands toward the blade.
origin: schoology

- q: How do you check that the blade runs in the middle of the wheels (tracking)?
choices: [Turn the power on for short bursts, Open the covers while it coasts, Turn the wheel by hand with the power off, Open the covers while braking]
answer: "Turn the wheel by hand with the power off"
why: The covers only come off with the power off, and turning by hand shows where the blade rides.
origin: schoology

- q: While making a cut, you...
choices: [talk to your helper, concentrate on the cut, look around the shop, think about your next job]
answer: "concentrate on the cut"
why: Your full attention stays on the blade and your hands until the cut is done.
origin: schoology

- q: When do you clear scrap from the band saw table?
choices: [While you cut, When a lot has built up, After the saw has stopped, It depends on the job]
answer: "After the saw has stopped"
why: Reaching near a moving blade to clear scraps is how fingers get cut.
origin: schoology

- q: You need to back the blade out of a cut. What do you do?
choices: ["Turn the power off, wait for it to stop, then free the blade", "Leave the power on and loosen the tension", "Leave the power on so it slides out", "Use the brake while it runs"]
answer: "Turn the power off, wait for it to stop, then free the blade"
why: Backing out of a running cut can pull the blade off the wheels.
origin: schoology
review: true # added "wait for it to stop"

- q: The blade breaks while you are cutting. What do you do?
choices: ["Grab the blade", "Step back, switch off, keep the covers closed until the wheels stop, and tell a mentor", "Open the cover to see what happened", "Keep cutting with what is left"]
answer: "Step back, switch off, keep the covers closed until the wheels stop, and tell a mentor"
why: A broken blade can whip around inside the covers. Let everything stop, then a mentor replaces it.
origin: new
review: true

- q: How do you cut round stock (tube, dowel, bar) on the band saw?
choices: ["Freehand, held tight", "Clamped in a V-block or vise", "Rolling it into the blade", "Only with a helper holding it"]
answer: "Clamped in a V-block or vise"
why: The blade spins round stock and can pull your hand in. Clamped, it can't roll.
origin: new
review: true

- q: The blade slows down or the cut is drifting. What should you do?
choices: [Push harder, Ease off and let the blade cut at its own pace, Twist the stock to steer it, Speed up the feed to finish quickly]
answer: "Ease off and let the blade cut at its own pace"
why: Forcing the feed bends or breaks the blade. Let the teeth do the work.
origin: new
review: true

- q: What do you do before you walk away from the band saw?
choices: [Switch off and wait until the blade stops completely, Switch off and leave right away, Leave it running for the next person, Lower the guard and leave it running]
answer: "Switch off and wait until the blade stops completely"
why: A coasting blade is silent and nearly invisible to the next person.
origin: new
review: true

- q: Where do you stand while cutting?
choices: [Directly behind the blade, Slightly to one side of the blade's path, On the right side reaching around, Wherever is comfortable]
answer: "Slightly to one side of the blade's path"
why: If the blade breaks or the stock kicks, you are out of its line.
origin: new
review: true

- q: What does the blade tensioning knob (on top of the saw) do?
choices: [Raises the blade guard, Tightens or loosens the blade on the wheels, Tilts the table, Turns on the light]
answer: "Tightens or loosens the blade on the wheels"
why: Correct tension keeps the blade tracking and cutting straight. Only adjust it with the power off.
origin: new
review: true

- q: What is the guide post for?
choices: [Raising or lowering the upper guard and blade guides to just above the stock, Tilting the table, Holding the stock, Changing the speed]
answer: "Raising or lowering the upper guard and blade guides to just above the stock"
why: Set it, then lock it with the guide post locking knob before cutting.
origin: new
review: true

- q: What do the blade guides and the thrust bearing do?
choices: [Keep the blade from twisting and from being pushed back during the cut, Sharpen the blade, Hold the stock flat, Adjust the speed]
answer: "Keep the blade from twisting and from being pushed back during the cut"
why: The guides stop side-to-side twist; the thrust bearing behind the blade takes the push of the feed.
origin: new
review: true

- q: What is the table insert (the plate around the blade in the table) for?
choices: [Supporting the stock right next to the blade so small pieces don't fall in, Locking the table angle, Holding the blade guard, Catching sawdust only]
answer: "Supporting the stock right next to the blade so small pieces don't fall in"
why: A missing or worn insert lets offcuts drop into the saw and jam the blade.
origin: new
review: true

- q: Where is the power switch, and how do you use it in an emergency?
choices: [On the front of the base - you switch it off right away, There isn't one, Behind the saw - you unplug it, On the guide post]
answer: "On the front of the base - you switch it off right away"
why: Know where the switch is before you start, so you can hit it without looking.
origin: new
review: true # check against our saw's switch location
115 changes: 115 additions & 0 deletions content/raptacon/quizzes/drill-press.yml
Original file line number Diff line number Diff line change
@@ -0,0 +1,115 @@
# Drill press: the written half of tool-drill-press. Questions 1-12 are the Schoology
# "Drill Press Quiz" (ID 5867); 13-16 are new (gloves, speed, center punch, chips).

quiz:
id: drill-press
name: Drill press safety quiz
item: tool-drill-press
pass: 100
authored_by: # Corey and Marilyn wrote the Schoology originals; Chris added the new questions
- {name: Corey Kesler}
- {name: Marilyn Kemp}
- {name: Chris Hirsch, github: ChrisHirsch}
source: Schoology "Drill Press Quiz" (ID 5867)

questions:
- q: What do you do with long hair at the drill press?
choices: ["Keep your head back", "Get a haircut", "Tie it back or put it under a cap, and keep your head away from moving parts", "Hold it away with one hand"]
answer: "Tie it back or put it under a cap, and keep your head away from moving parts"
why: The spindle winds hair in faster than you can react.
origin: schoology

- q: Which protective equipment is absolutely required at the drill press?
choices: [Safety glasses, Steel-toed shoes, A leather apron, Leather gloves]
answer: "Safety glasses"
why: Chips fly off the bit. And no gloves near the spinning chuck.
origin: schoology

- q: Which of these makes the drill press unsafe to use?
choices: [Slippery floor from spilled cutting oil, Tools and scrap cluttering the table, A loose belt guard, All of these]
answer: "All of these"
why: Fix each one before you start.
origin: schoology

- q: The part starts spinning with the bit. What do you do?
choices: ["Move the table to block it", "Stop it with your hands", "Tap it with a hammer", "Switch off, let it stop, then free the part"]
answer: "Switch off, let it stop, then free the part"
why: A spinning part is a blade. Never grab it.
origin: schoology

- q: You are drilling a material you haven't drilled before. You always...
choices: [make sure you have the right bit, unplug it and inspect the guide, oil the bit, check with a mentor first]
answer: "check with a mentor first"
why: Different materials need different bits, speeds and clamping.
origin: schoology

- q: Before turning on the drill press, you...
choices: [tighten the table lock, clamp the work in a vise or to the table, remove the chuck key, do all of these]
answer: "do all of these"
why: A chuck key left in the chuck becomes a projectile when the spindle starts.
origin: schoology

- q: Which is NOT a safe way to hold metal for drilling?
choices: [Between stops mounted on the table, A clamp, A drill press vise, Holding it firmly by hand on the table]
answer: "Holding it firmly by hand on the table"
why: If the bit grabs, a hand-held part spins and cuts you.
origin: schoology

- q: When a bit seizes (grabs), it can...
choices: [break the bit, spin the vise, slip in the chuck, do all of these]
answer: "do all of these"
why: That's why the work is clamped and you ease off the feed.
origin: schoology

- q: When you finish drilling, what do you do first?
choices: [Take the part out of the vise, Take the bit out of the chuck, Switch off the drill press, Nothing]
answer: "Switch off the drill press"
why: Hands near the work only after the spindle has stopped.
origin: schoology

- q: How do you drill a long piece?
choices: [Support only the clamped end, Put the long end to your right, Support the far (unclamped) end, Nothing special]
answer: "Support the far (unclamped) end"
why: An unsupported long piece tips and twists the part out of the vise.
origin: schoology

- q: After drilling, which hazard should you watch for?
choices: [Stress in the material, Hot cutting oil, Sharp edges and burrs around the hole, A dull bit]
answer: "Sharp edges and burrs around the hole"
why: Deburr the hole before handling the part.
origin: schoology

- q: How do you keep the bit from seizing as it goes through?
choices: [Put wood under the part, Slow the bit down, Ease off the feed pressure as the bit breaks through, Keep the bit oiled]
answer: "Ease off the feed pressure as the bit breaks through"
why: The bit grabs most as it breaks through the far side. Ease off there.
origin: schoology
review: true # original key said "as the bit begins to cut"; changed to "breaks through"

- q: Do you wear gloves at the drill press?
choices: ["Yes, to protect your hands", "No - a glove can catch on the bit or chuck and pull your hand in", "Only leather gloves", "Only for metal"]
answer: "No - a glove can catch on the bit or chuck and pull your hand in"
why: Bare hands, clamped work.
origin: new
review: true

- q: How does bit size change the spindle speed?
choices: [Bigger bits need a slower speed, Bigger bits need a faster speed, Speed doesn't matter, Always use the fastest speed]
answer: "Bigger bits need a slower speed"
why: A big bit at high speed overheats and grabs. Check the speed chart, or ask a mentor.
origin: new
review: true

- q: What do you do before drilling a hole in metal?
choices: [Center punch the mark, Nothing, Oil your hands, Heat the metal]
answer: "Center punch the mark"
why: The punch mark keeps the bit from wandering off your layout line.
origin: new
review: true

- q: How do you clear chips from the table?
choices: ["With a brush, after the spindle stops", "With your hand while it runs", "Blow them at someone", "Leave them"]
answer: "With a brush, after the spindle stops"
why: Metal chips are razor sharp, and hot.
origin: new
review: true
Loading
Loading